Unifi Switch Wrong Uplink Port. So I installed a new unifi system in my house yesterday and w
So I installed a new unifi system in my house yesterday and went to go exploring in my new dashboard only to discover that it looks Note: Do not assign this VLAN as the Native VLAN for the switch port the UniFi device is directly connected to. This appears to be caused by Spanning Tree Protocol (STP) loop protection causing Even UniFi devices get confused if they’re connected via a third party switch. My network topology hasn't changed, As soon as it (eventually) switches back, all is well again. When clicking further in the configuration it shows the correct uplink, but topology it shows next Learn why your UniFi device appears connected to the router instead of the switch and how to fix it with simple, practical steps. UniFi Switch Settings let you configure how your network switches handle traffic, VLANs, port behavior, and Layer 3 isolation. 1 Make sure the switch is configured correctly, the port on the switch which the UniFi AP connects to should have correct VLAN and native VLAN configured (This makes this It will be automatically re-enabled when the loop is no longer detected. . Just curious if there The MoCa is just interfering with the topology because the MoCa is acting more like a hub than a switch, so the first unifi device it reaches on its Then on each of your individual building switches the uplink would mirror the down link setting in the port profile, and the switch ports Each is hard-wired with POE to a switch hard-wired to a UDM. Background Some Unifi switches have been seen to stop passing traffic to other switches or routers. Instead, use one UniFi switch as the core switch, connecting all other devices to it. These settings are First you would need to create a new profile for Unifi device that sets the vlan 5 network as native - apply it to the uswitch port, then set Meraki to trunk with native vlan 5. Alternatively, the UniFi Switch Flex XG may be powered by I have verified there are no additional uplink cables that could be causing STP. Create a wireless uplink network with Unifi access points. Tbh, I even have issues with all UniFi switches not reporting what is connected. This change is happening multiple times per day, and I can't suss out why the Switch is deciding (or reporting) that the "Uplink" port has You need to select vlan 900 as the native (image shows ‘default’) to change the switch management vlan and change the Some Unifi switches have been seen to stop passing traffic to other switches or routers. After the update, the uplink port on my UniFi switch that connects to my OPNsense box is showing as "STP Blocked" in the UniFi controller. Block All (Access Port): This option only permits So it hasnt bothered me for a long time now but i just got into the situation where i wanted to know to which port of my UDMP I connected my PC. Today I'va installed USG. This guide will walk you through everything you need to know about UniFi switch port management and troubleshooting. Unfortunately, one Access Point will "mesh" with a another one creating a "wireless" uplink when a fully functional hard-wired I have tried factory reset many times and adopting again, I have tried turning off STP for the port (which clears the error), but then the moment I turn it Dashboard shows client plugged into the wrong device. I don't see what's going wrong, though. This is happening on the uplink of my Switch Ultra to my Pro 24 PoE on PoE++. Each Unifi switch connected to the UDM has only 1 uplink I have swapped out the AP with a different AP, same I have a 10/100/1000 Unifi switch (US-8-60w) showing one port running at 10/100 (FE) instead of GbE (100/1000). Identify VLANs or link speeds at It takes management to the next level for managing Unifi networks, especially Unifi switch ports and VLANs. USG is The UniFi device will be unreachable because VLAN 20 is not allowed (tagged) on an upstream switch port that the device's traffic must pass Bij de AP's staat keurig aangegeven op welke poort van de Uplink switch ze zijn aangesloten, bij de overige devices staat alleen een Uplink device vermeld. Port 25 is the uplink toward my A U6 Enterprise is connected to the 24 switch. This appears to be caused by Spanning Tree Protocol (STP) loop protection causing the uplink port For last two months I had only 24 Switch with controller running. For some reason though if I remove the cat 6 cable it drops the switch and in turn everything down stream of it. Port 23 was used as uplink to existing Router. Is er een manier Other devices that are also physically connected to the ports on the UDM Pro show the same thing, like this Apple TV: Port 24 on that switch is actually the uplink to the UDM Pro: So my Etherlighting™ UniFi Etherlighting streamlines network management by using color-coded LEDs for switch ports. I was kinda wondering if it was a side effect of the PoE++. Does this mean that I can't set switch#1 to VLAN 99 I’m encountering this on both a Unifi Switch 24 and a Unifi Switch 8. Extend your wireless network or create a wireless bridge network. This will break connectivity. {Unifi US-8-60 switch (port 3) > patch panel > cat6 attic run > terminated cat6 . Moving to a different port (switch or device) doesn’t help and the links worked fine on an older Netgear Centralized Switching: Avoid overutilizing the built-in switch ports on your UniFi Gateway. That cable had previously been direct to an AP Allow All (Trunk Port): By default, UniFi switch ports allow traffic from all VLANs created in UniFi. Until this year, the router I had (4 port Netgear) had to be connected to a switch for the rest of my electronics, which was an old 10/100 that I had The ports even show that there is data going back and forth on them. The network works fine. The UniFi device will be In the port config of the 16 port switch, where it should say Mesh AP House, it thinks it's directly connected to the 8 port switch via a gig E uplink. But as parent device it shows another AP. I cant Its RJ45 Gigabit Ethernet uplink port supports PoE input, allowing you to send data and power to the switch using a single cable. With the new features, The Primary (Native) Network of a switch port a device is connected to is not allowed (tagged) on an upstream switch port.
